Comline Termination Board/ Lightning Protection
Our Comline Termination Board enables a neat and proper termination for each and every pair of the comline. Making sure that all pairs are properly terminated is imperative to protecting the lift equipment from lightning or other problems that can come back down the comline. Everything is clearly labeled and there is a schematic that explains exactly what is being used on the board for lightning protection. Utilizing a resistor, poly-switch, trans-orb, gas discharge tube, and fuse these boards offer the best lightning protection on the market, in use they have worked flawlessly in protecting the lift equipment in the motor room and shack from any problems the com-line might face.
This board is magnetically mounted enabling easy installation and has quick connectors on each side easing installation and troubleshooting.
This board is magnetically mounted enabling easy installation and has quick connectors on each side easing installation and troubleshooting.
Efector Tester
The Efector tester provides a both positive and negative test for Efector switches. Utilizing a simple LED you are given a go or no go test for the switch. The tester is self powered by standard nine volt batteries enabling it to be used anywhere on the mountain without having to worry about power. As the tester is inactive until a switch is plugged in to one of two plugs (both old and new versions) the battery life is greatly extended.
No Dial Weatherized Phone
Our no dial phones offer a reliable and economical replacement for sound powered and other electric phones. With no dialpad or ringer to break, these phones provide trouble free service. They magnetically mount allowing for easy installation and flexibility of location. They are built with a female jack so that cords can be easily and cheaply replaced without having to do any wiring.
Phone Conversion Module
Our phone conversion module converts your lifts phone from sound powered to electric power for more reliable performance and better sound. These modules hook right into 24v power and don't need an adapter or inverter. There are four slots for phones and more can be daisy chained in as well. Magnetically mounts and works with any and all standard electric phones, so if one breaks you can even grab one from the lodge to get you through the day.
Push Button Stations
Our push button stations are resort tested and the design has been used in the field for nearing a decade now of reliable service.Each button returns two wires to the connected control (dry contact) - allowing a variety of connection schemes. The Emergency Stop button is on a different plane encouraging operators to use the normal stop button first. The station comes complete with an interior heating element to prevent any stuck or sticky buttons as well as minimize any condensation inside the station. With a weathertight casing and weathertight phone and input jack no matter what the conditions our stations function correctly day in day out. Included inside the casing is a full schematic for any trouble shooting needed.The legend panel is reverse engraved (from the back) and backfilled with the colors you select. This ensures an easily read, easily cleaned and long lasting panel. They are also fully customizable and you the customer can decide which functions are included on the station, and where they are located, enabling you to best suit the station to your operation. With a quick disconnect these stations are designed to come in to the lift shack every night helping prevent damage from snowcats, or theft.
Proxy Safe
Proxy Safe is a simple module that hooks inline in front of Doppelmayr Proximity sensors to protect high risk areas from lightning strikes. These modules protect the sensors when the tower system is on or off. In on lift testing they have worked brilliantly and prevented countless proxy sensors from being destroyed by lightning. Their simple design, including a magnetic mounting system make installation a no tools job, simply unplug the proxy sensor from the tower cable and hook the module in between the two using the standard style 4 prong connectors.
Rope Proximity Sensor
This Proximity sensor takes out the complex and unreliable electronics found in other proximity sensors and replaces it with a simple magnetic system. This makes the switch much less likely to fail due to stray voltages, or weather intrusion. The switch utilizes only two wires instead of the standard four, making wiring easier, and less troublesome on the cross arm. It can be wired via the easy banana plug, or screw connections. The simple reset tool forces the lift mechanic to make sure that there are no issues on the tower, preventing faults from being ignored...
Brittle Bar Deropement Switch DR2
This brittle bar is an exact replacement for Lift Engineering DR switches with a few improvements. First it does not need the pigtail of wires, and instead makes the connection right at the switch. This solves the problem of the two wires rubbing against each other and shorting out inside the plastic boot, thus preventing the switch from giving meaningful feedback. This also reduces the cost of the switch as you do not need to buy the wired pigtail with the switch each time the switch needs replaced. Finally with the new connector provided with each switch one can replace a switch in mere seconds. And given the four space ability of the connector multiple Brittle Bars can be chained together as your tower configuration requires. The sliding bolt hole also enables flexibility in terms of DR switch length, where brackets may not be the exact length of a standard DR switch.